mirror of
https://github.com/trezor/trezor-firmware.git
synced 2024-11-01 04:49:31 +00:00
81 lines
3.4 KiB
C
81 lines
3.4 KiB
C
/*
|
|
* This file is part of the TREZOR project, https://trezor.io/
|
|
*
|
|
* Copyright (c) SatoshiLabs
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include STM32_HAL_H
|
|
|
|
#include "rng.h"
|
|
|
|
const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
|
|
const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
|
|
|
|
uint32_t SystemCoreClock = 168000000U;
|
|
|
|
#pragma GCC optimize("no-stack-protector") // applies to all functions in this file
|
|
|
|
void SystemInit(void)
|
|
{
|
|
// set flash wait states for an increasing HCLK frequency -- reference RM0090 section 3.5.1
|
|
FLASH->ACR = FLASH_ACR_LATENCY_5WS;
|
|
// wait until the new wait state config takes effect -- per section 3.5.1 guidance
|
|
while ((FLASH->ACR & FLASH_ACR_LATENCY) != FLASH_ACR_LATENCY_5WS);
|
|
// configure main PLL; assumes HSE is 8 MHz; this should evaluate to 0x27402a04 -- reference RM0090 section 7.3.2
|
|
RCC->PLLCFGR = (RCC_PLLCFGR_RST_VALUE & ~RCC_PLLCFGR_PLLQ & ~RCC_PLLCFGR_PLLSRC & ~RCC_PLLCFGR_PLLP & ~RCC_PLLCFGR_PLLN & ~RCC_PLLCFGR_PLLM)
|
|
| (7U << RCC_PLLCFGR_PLLQ_Pos) // Q = 7
|
|
| RCC_PLLCFGR_PLLSRC_HSE // PLLSRC = HSE
|
|
| (0U << RCC_PLLCFGR_PLLP_Pos) // P = 2 (two bits, 00 means PLLP = 2)
|
|
| (168U << RCC_PLLCFGR_PLLN_Pos) // N = 168
|
|
| (4U << RCC_PLLCFGR_PLLM_Pos); // M = 4
|
|
// enable spread spectrum clock for main PLL
|
|
RCC->SSCGR = RCC_SSCGR_SSCGEN | (44 << RCC_SSCGR_INCSTEP_Pos) | (250 << RCC_SSCGR_MODPER_Pos);
|
|
// enable clock security system, HSE clock, and main PLL
|
|
RCC->CR |= RCC_CR_CSSON | RCC_CR_HSEON | RCC_CR_PLLON;
|
|
// wait until PLL and HSE ready
|
|
while((RCC->CR & (RCC_CR_PLLRDY | RCC_CR_HSERDY)) != (RCC_CR_PLLRDY | RCC_CR_HSERDY));
|
|
// APB2=2, APB1=4, AHB=1, system clock = main PLL
|
|
const uint32_t cfgr = RCC_CFGR_PPRE2_DIV2 | RCC_CFGR_PPRE1_DIV4 | RCC_CFGR_HPRE_DIV1 | RCC_CFGR_SW_PLL;
|
|
RCC->CFGR = cfgr;
|
|
// wait until PLL is system clock and also verify that the pre-scalers were set
|
|
while(RCC->CFGR != (RCC_CFGR_SWS_PLL | cfgr));
|
|
// turn off the HSI as it is now unused (it will be turned on again automatically if a clock security failure occurs)
|
|
RCC->CR &= ~RCC_CR_HSION;
|
|
// wait until ths HSI is off
|
|
while((RCC->CR & RCC_CR_HSION) == RCC_CR_HSION);
|
|
// init the TRNG peripheral
|
|
rng_init();
|
|
// set CP10 and CP11 to enable full access to the fpu coprocessor; ARMv7-M Architecture Reference Manual section B3.2.20
|
|
SCB->CPACR |= ((3U << 22) | (3U << 20));
|
|
}
|
|
|
|
extern volatile uint32_t uwTick;
|
|
|
|
void SysTick_Handler(void)
|
|
{
|
|
// this is a millisecond tick counter that wraps after approximately
|
|
// 49.71 days = (0xffffffff / (24 * 60 * 60 * 1000))
|
|
uwTick++;
|
|
}
|
|
|
|
void shutdown(void);
|
|
|
|
void PVD_IRQHandler(void)
|
|
{
|
|
TIM1->CCR1 = 0; // turn off display backlight
|
|
shutdown();
|
|
}
|