linux-insides/Booting/linux-bootstrap-2.md

Kernel booting process. Part 2.

First steps in the kernel setup

We started to dive into linux kernel internals in the previous part and saw the initial part of the kernel setup code. We stopped at the first call of the main function (which is the first function written in C) from arch/x86/boot/main.c. Here we will continue to research the kernel setup code and see what is protected mode, some preparation for the transition into it, the heap and console initialization, memory detection and much much more. So... Let's go ahead.

Protected mode

Before we can move to the native Intel64 Long mode, the kernel must switch the CPU into protected mode. What is the protected mode? The Protected mode was first added to the x86 architecture in 1982 and was the main mode of Intel processors from 80286 processor until Intel 64 and long mode. The Main reason to move away from the real mode that there is very limited access to the RAM. As you can remember from the previous part, there is only 2^20 bytes or 1 megabyte, sometimes even only 640 kilobytes.

Protected mode brought many changes, but the main is a different memory management.The 24-bit address bus was replaced with a 32-bit address bus. It allows to access to 4 gigabytes of physical adress space. Also paging support was added which we will see in the next parts.

Memory management in the protected mode is divided into two, almost independent parts:

• Segmentation
• Paging

Here we can only see segmentation. As you can read in the previous part, addresses consist of two parts in the real mode:

• Base address of segment
• Offset from the segment base

And we can get the physical address if we know these two parts by:

PhysicalAddress = Segment * 16 + Offset

Memory segmentation was completely redone in the protected mode. There are no 64 kilobytes fixed-size segments. All memory segments are described by the Global Descriptor Table (GDT) instead of segment registers.The GDT is a structure which resides in memory. There is no fixed place for it in memory, but its address is stored in the special GDTR register. Later we will see the GDT loading in the linux kernel code. There will be an operation for loading it into memory, something like:

lgdt gdt

where the lgdt instruction loads the base address and limit of global descriptor table to the GDTR register. GDTR is a 48-bit register and consists of two parts:

• size - 16 bit of global descriptor table;
• address - 32-bit of the global descriptor table.

The global descriptor table contains descriptors which describe memory segments. Every descriptor is 64-bit. General scheme of a descriptor is:

31          24        19      16              7            0
------------------------------------------------------------
|             | |B| |A|       | |   | |0|E|W|A|            |
| BASE 31..24 |G|/|L|V| LIMIT |P|DPL|S|  TYPE | BASE 23:16 | 4
|             | |D| |L| 19..16| |   | |1|C|R|A|            |
------------------------------------------------------------
|                             |                            |
|        BASE 15..0           |       LIMIT 15..0          | 0
|                             |                            |
------------------------------------------------------------

Don't worry, i know that it looks a little scary after real mode, but it's easy. Let's look on it closer:

1. Limit (0 - 15 bits) defines a length_of_segment - 1. It depends on G bit.

• if G (55-bit) is 0 and segment limit is 0 - size of segment - 1 byte
• if G is 1 and segment limit is 0 - size of segment 4096 bytes
• if G is 0 and segment limit is 0xfffff - size of segment 1 megabyte
• if G is 1 and segment limit is 0xfffff - size of segment 4 gigabytes

2. Base (0-15, 32-39 and 56-63 bits) defines the physical address of the segment's start address.

3. Type (40-47 bits) defines the type of segment and kinds of access to it. Next S flag specifies descriptor type. if S is 0 - this segment is a system segment, if S is 1 - code or data segment (Stack segments are data segments which must be read/write segments). If the segment is a code or data segment, it can be one of the following access types:

|           Type Field        | Descriptor Type | Description
|-----------------------------|-----------------|------------------
| Decimal                     |                 |
|             0    E    W   A |                 |
| 0           0    0    0   0 | Data            | Read-Only
| 1           0    0    0   1 | Data            | Read-Only, accessed
| 2           0    0    1   0 | Data            | Read/Write
| 3           0    0    1   1 | Data            | Read/Write, accessed
| 4           0    1    0   0 | Data            | Read-Only, expand-down
| 5           0    1    0   1 | Data            | Read-Only, expand-down, accessed
| 6           0    1    1   0 | Data            | Read/Write, expand-down
| 7           0    1    1   1 | Data            | Read/Write, expand-down, accessed
|                  C    R   A |                 |
| 8           1    0    0   0 | Code            | Execute-Only
| 9           1    0    0   1 | Code            | Execute-Only, accessed
| 10          1    0    1   0 | Code            | Execute/Read
| 11          1    0    1   1 | Code            | Execute/Read, accessed
| 12          1    1    0   0 | Code            | Execute-Only, conforming
| 14          1    1    0   1 | Code            | Execute-Only, conforming, accessed
| 13          1    1    1   0 | Code            | Execute/Read, conforming
| 15          1    1    1   1 | Code            | Execute/Read, conforming, accessed

As we can see the first bit is 0 for data segment and 1 for code segment. Next three bits EWA are expansion direction (expand-down segment will grow down, you can read more about it here), write enable and accessed for data segments. CRA bits are conforming (A transfer of execution into a more-privileged conforming segment allows execution to continue at the current privilege level), read enable and accessed.

4. DPL (descriptor privilege level) defines the privilege level of the segment. It can be 0-3 where 0 is the most privileged.

5. P flag - indicates if segment is present in memory or not.

6. AVL flag - Available and reserved bits.

7. L flag - indicates whether a code segment contains native 64-bit code. If 1 then the code segment executes in 64 bit mode.

8. B/D flag - default operation size/default stack pointer size and/or upper bound.

Segment registers don't contain the base address of the segment as in the real mode. Instead they contain a special structure - segment selector. Selector is a 16-bit structure:

-----------------------------
|       Index    | TI | RPL |
-----------------------------

Where Index shows the index number of the descriptor in descriptor table. TI shows where to search for the descriptor: in the global descriptor table or local. And RPL is the privilege level.

Every segment register has a visible and hidden part. When a selector is loaded into one of the segment registers, it will be stored into the visible part. The hidden part contains the base address, limit and access information of the descriptor which pointed to the selector. The following steps are needed to get the physical address in the protected mode:

• Segment selector must be loaded in one of the segment registers;
• CPU tries to find (by GDT address + Index from selector) and load the descriptor into the hidden part of segment register;
• Base address (from segment descriptor) + offset will be the linear address of the segment which is the physical address (if paging is disabled).

Schematically it will look like this:

THe algorithm for the transition from the real mode into protected mode is:

• Disable interrupts;
• Describe and load GDT with lgdt instruction;
• Set PE (Protection Enable) bit in CR0 (Control Register 0);
• Jump to protected mode code;

We will see the transition to the protected mode in the linux kernel in the next part, but before we can move to protected mode, we need to do some preparations.

Let's look on arch/x86/boot/main.c. We can see some routines there which make keyboard initialization, heap initialization, etc... Let's look into it.

Copying boot parameters into the "zeropage"

We will start from the main routine in "main.c". First function which is called in main is copy_boot_params. It copies the kernel setup header into the field of the boot_params structure which is defined in the arch/x86/include/uapi/asm/bootparam.h.

The boot_params structure contains the struct setup_header hdr field. This structure contains the same fields as defined in linux boot protocol and is filled by the boot loader and also at kernel compile/build time. copy_boot_params does two things: copies hdr from header.S to the boot_params structure in setup_header field and updates pointer to the kernel command line if the kernel was loaded with old command line protocol.

Note that it copies hdr with memcpy function which is defined in the copy.S source file. Let's have a look inside:

GLOBAL(memcpy)
	pushw	%si
	pushw	%di
	movw	%ax, %di
	movw	%dx, %si
	pushw	%cx
	shrw	$2, %cx
	rep; movsl
	popw	%cx
	andw	$3, %cx
	rep; movsb
	popw	%di
	popw	%si
	retl
ENDPROC(memcpy)

Yeah, we just moved to C code and now assembly again :) First of all we can see that memcpy and other routines which are defined here, start and end with the two macros: GLOBAL and ENDPROC. GLOBAL is described in arch/x86/include/asm/linkage.h which defines globl directive and the label for it. ENDPROC is described in include/linux/linkage.h which marks name symbol as function name and ends with the size of the name symbol.

Implementation of the memcpy is easy. At first, it pushes values from si and di registers to the stack because their values will change in the memcpy, so push it on the stack to preserve their values. memcpy (and other functions in copy.S) use fastcall calling conventions. So it gets incoming parameters from the ax, dx and cx registers. Calling memcpy looks like this:

memcpy(&boot_params.hdr, &hdr, sizeof hdr);

So ax will contain the address of the boot_params.hdr, dx will contain the address of hdr and cx will contain the size of hdr (all in bytes). memcpy puts the address of boot_params.hdr to the di register and address of hdr to si and saves the size on the stack. After this it shifts to the right on 2 size (or divide on 4) and copies from si to di by 4 bytes. After it we restore the size of hdr again, align it by 4 bytes and copy the rest of bytes from si to di byte by byte (if there is rest). Restore si and di values from the stack in the end and after this copying is finished.

Console initialization

After the hdr is copied into boot_params.hdr, the next step is console initialization by calling the console_init function which is defined in arch/x86/boot/early_serial_console.c.

It tries to find the earlyprintk option in the command line and if the search was successful, it parses the port address and baud rate of the serial port and initializes the serial port. Value of earlyprintk command line option can be one of the:

* serial,0x3f8,115200
* serial,ttyS0,115200
* ttyS0,115200

After serial port initialization we can see the first output:

if (cmdline_find_option_bool("debug"))
		puts("early console in setup code\n");

puts definition is in tty.c. As we can see it prints character by character in the loop by calling The putchar function. Let's look into the putchar implementation:

void __attribute__((section(".inittext"))) putchar(int ch)
{
	if (ch == '\n')
		putchar('\r');

	bios_putchar(ch);

	if (early_serial_base != 0)
		serial_putchar(ch);
}

__attribute__((section(".inittext"))) means that this code will be in the .inittext section. We can find it in the linker file setup.ld.

First of all, put_char checks for the \n symbol and if it is found, prints \r before. After that it outputs the character on the VGA screen by calling the BIOS with the 0x10 interrupt call:

static void __attribute__((section(".inittext"))) bios_putchar(int ch)
{
	struct biosregs ireg;

	initregs(&ireg);
	ireg.bx = 0x0007;
	ireg.cx = 0x0001;
	ireg.ah = 0x0e;
	ireg.al = ch;
	intcall(0x10, &ireg, NULL);
}

Here initregs takes the biosregs structure and first fills biosregs with zeros using the memset function and then fills it with register values.

	memset(reg, 0, sizeof *reg);
	reg->eflags |= X86_EFLAGS_CF;
	reg->ds = ds();
	reg->es = ds();
	reg->fs = fs();
	reg->gs = gs();

Let's look on the memset implementation:

GLOBAL(memset)
	pushw	%di
	movw	%ax, %di
	movzbl	%dl, %eax
	imull	$0x01010101,%eax
	pushw	%cx
	shrw	$2, %cx
	rep; stosl
	popw	%cx
	andw	$3, %cx
	rep; stosb
	popw	%di
	retl
ENDPROC(memset)

As you can read above, it uses fastcall calling conventions like the memcpy function, which means that the function gets parameters from ax, dx and cx registers.

Generally memset is like a memcpy implementation. It saves the value of the di register on the stack and puts the ax value into di which is the address of the biosregs structure. Next is the movzbl instruction, which copies the dl value to the low 2 bytes of the eax register. The remaining 2 high bytes of eax will be filled with zeros.

The next instruction multiplies eax with 0x01010101. It needs to because memset will copy 4 bytes at the same time. For example we need to fill a structure with 0x7 with memset. eax will contain 0x00000007 value in this case. So if we multiply eax with 0x01010101, we will get 0x07070707 and now we can copy these 4 bytes into the structure. memset uses rep; stosl instructions for copying eax into es:di.

The rest of the memset function does almost the same as memcpy.

After that biosregs structure is filled with memset, bios_putchar calls the 0x10 interrupt which prints a character. Afterwards it checks if the serial port was initialized or not and writes a character there with serial_putchar and inb/outb instructions if it was set.

Heap initialization

After the stack and bss section were prepared in header.S (see previous part), the kernel needs to initialize the heap with the init_heap function.

First of all init_heap checks the CAN_USE_HEAP flag from the loadflags kernel setup header and calculates the end of the stack if this flag was set:

	char *stack_end;

	if (boot_params.hdr.loadflags & CAN_USE_HEAP) {
		asm("leal %P1(%%esp),%0"
		    : "=r" (stack_end) : "i" (-STACK_SIZE));

or in other words stack_end = esp - STACK_SIZE.

Then there is the heap_end calculation which is heap_end_ptr or _end + 512 and a check if heap_end is greater than stack_end makes it equal.

From this moment we can use the heap in the kernel setup code. We will see how to use it and how the API for it is implemented in next posts.

CPU validation

The next step as we can see is cpu validation by validate_cpu from arch/x86/boot/cpu.c.

It calls the check_cpu function and passes cpu level and required cpu level to it and checks that kernel launched at the right cpu. It checks the cpu's flags, presence of long mode (which we will see more details on in the next parts) for x86_64, checks the processor's vendor and makes preparation for certain vendors like turning off SSE+SSE2 for AMD if they are missing and etc...

Memory detection

The next step is memory detection by the detect_memory function. It uses different programming interfaces for memory detection like 0xe820, 0xe801 and 0x88. We will see only the implementation of 0xE820 here. Let's look into the detect_memory_e820 implementation from the arch/x86/boot/memory.c source file. First of all, detect_memory_e820 function initializes biosregs structure as we saw above and fills registers with special values for the 0xe820 call:

	initregs(&ireg);
	ireg.ax  = 0xe820;
	ireg.cx  = sizeof buf;
	ireg.edx = SMAP;
	ireg.di  = (size_t)&buf;

The ax register must contain the number of the function (0xe820 in our case), cx register contains size of the buffer which will contain data about memory, edx must contain the SMAP magic number, es:di must contain the address of the buffer which will contain memory data and ebx has to be zero.

Next is a loop where data about the memory will be collected. It starts from the call of the 0x15 bios interrupt, which writes one line from the address allocation table. For getting the next line we need to call this interrupt again (which we do in the loop). Before the next call ebx must contain the value returned previously:

	intcall(0x15, &ireg, &oreg);
	ireg.ebx = oreg.ebx;

Ultimately, it does iterations in the loop to collect data from the address allocation table and writes this data into the e820entry array:

• start of memory segment
• size of memory segment
• type of memory segment (which can be reserved, usable and etc...).

You can see the result of this in the dmesg output, something like:

[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000003ffdffff] usable
[    0.000000] BIOS-e820: [mem 0x000000003ffe0000-0x000000003fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved

Keyboard initialization

The next step is the initialization of the keyboard with the call of the keyboard_init function. At first keyboard_init initializes registers using the initregs function and calling the 0x16 interrupt for getting the keyboard status. After this it calls 0x16 again to set repeat rate and delay.

Querying

The next couple of steps are queries for different parameters. We will not dive into details about these queries, but will be back to the all of it in the next parts. Let's make a short look on this functions:

The query_mca routine calls the 0x15 BIOS interrupt to get the machine model number, sub-model number, BIOS revision level, and other hardware-specific attributes:

int query_mca(void)
{
	struct biosregs ireg, oreg;
	u16 len;

	initregs(&ireg);
	ireg.ah = 0xc0;
	intcall(0x15, &ireg, &oreg);

	if (oreg.eflags & X86_EFLAGS_CF)
		return -1;	/* No MCA present */

	set_fs(oreg.es);
	len = rdfs16(oreg.bx);

	if (len > sizeof(boot_params.sys_desc_table))
		len = sizeof(boot_params.sys_desc_table);

	copy_from_fs(&boot_params.sys_desc_table, oreg.bx, len);
	return 0;
}

It fills the ah register with 0xc0 and calls the 0x15 BIOS interruption. After the interrupt execution it checks the carry flag and if it is set to 1, BIOS doesn't support MCA. If carry flag is set to 0, ES:BX will contain a pointer to the system information table, which looks like this:

Offset	Size	Description	)
 00h	WORD	number of bytes following
 02h	BYTE	model (see #00515)
 03h	BYTE	submodel (see #00515)
 04h	BYTE	BIOS revision: 0 for first release, 1 for 2nd, etc.
 05h	BYTE	feature byte 1 (see #00510)
 06h	BYTE	feature byte 2 (see #00511)
 07h	BYTE	feature byte 3 (see #00512)
 08h	BYTE	feature byte 4 (see #00513)
 09h	BYTE	feature byte 5 (see #00514)
---AWARD BIOS---
 0Ah  N BYTEs	AWARD copyright notice
---Phoenix BIOS---
 0Ah	BYTE	??? (00h)
 0Bh	BYTE	major version
 0Ch	BYTE	minor version (BCD)
 0Dh  4 BYTEs	ASCIZ string "PTL" (Phoenix Technologies Ltd)
---Quadram Quad386---
 0Ah 17 BYTEs	ASCII signature string "Quadram Quad386XT"
---Toshiba (Satellite Pro 435CDS at least)---
 0Ah  7 BYTEs	signature "TOSHIBA"
 11h	BYTE	??? (8h)
 12h	BYTE	??? (E7h) product ID??? (guess)
 13h  3 BYTEs	"JPN"

Next we call the set_fs routine and pass the value of the es register to it. Implementation of set_fs is pretty simple:

static inline void set_fs(u16 seg)
{
	asm volatile("movw %0,%%fs" : : "rm" (seg));
}

There is inline assembly which gets the value of the seg parameter and puts it into the fs register. There are many functions in boot.h like set_fs, for example set_gs, fs, gs for reading a value in it and etc...

In the end of query_mca it just copies the table which pointed to by es:bx to the boot_params.sys_desc_table.

The next is getting Intel SpeedStep information with the call of query_ist function. First of all it checks CPU level and if it is correct, calls 0x15 for getting info and saves the result to boot_params.

The following query_apm_bios function gets Advanced Power Management information from the BIOS. query_apm_bios calls the 0x15 BIOS interruption too, but with ah - 0x53 to check APM installation. After the 0x15 execution, query_apm_bios functions checks PM signature (it must be 0x504d), carry flag (it must be 0 if APM supported) and value of the cx register (if it's 0x02, protected mode interface is supported).

Next it calls the 0x15 again, but with ax = 0x5304 for disconnecting the APM interface and connect the 32bit protected mode interface. In the end it fills boot_params.apm_bios_info with values obtained from the BIOS.

Note that query_apm_bios will be executed only if CONFIG_APM or CONFIG_APM_MODULE was set in configuration file:

#if defined(CONFIG_APM) || defined(CONFIG_APM_MODULE)
	query_apm_bios();
#endif

The last is the query_edd function, which asks Enhanced Disk Drive information from the BIOS. Let's look into the query_edd implementation.

First of all it reads the edd option from kernel's command line and if it was set to off then query_edd just returns.

If EDD is enabled, query_edd goes over BIOS-supported hard disks and queries EDD information in the following loop:

	for (devno = 0x80; devno < 0x80+EDD_MBR_SIG_MAX; devno++) {
		if (!get_edd_info(devno, &ei) && boot_params.eddbuf_entries < EDDMAXNR) {
			memcpy(edp, &ei, sizeof ei);
			edp++;
			boot_params.eddbuf_entries++;
		}
		...
		...
		...

where the 0x80 is the first hard drive and the EDD_MBR_SIG_MAX macro is 16. It collects data into the array of edd_info structures. get_edd_info checks that EDD is present by invoking the 0x13 interrupt with ah as 0x41 and if EDD is present, get_edd_info again calls the 0x13 interrupt, but with ah as 0x48 and si contianing the address of the buffer where EDD informantion will be stored.

Conclusion

This is the end of the second part about linux kernel internals. In the next part we will see video mode setting and the rest of preparations before transition to protected mode and directly transitioning into it.

If you have any questions or suggestions write me a comment or ping me at twitter.

Please note that English is not my first language, And I am really sorry for any inconvenience. If you found any mistakes please send me PR to linux-internals.

Links

• Protected mode
• Long mode
• How to Use Expand Down Segments on Intel 386 and Later CPUs
• earlyprintk documentation
• Kernel Parameters
• Serial console
• Intel SpeedStep
• APM
• EDD specification
• Previous part