Kernel booting process. Part 1. ================================================================================ From the bootloader to kernel -------------------------------------------------------------------------------- If you have read my previous [blog posts](http://0xax.blogspot.com/search/label/asm), you can see that some time ago I started to get involved with low-level programming. I wrote some posts about x86_64 assembly programming for Linux. At the same time, I started to dive into the Linux source code. It is very interesting for me to understand how low-level things work, how programs run on my computer, how they are located in memory, how the kernel manages processes and memory, how the network stack works on low-level and many many other things. I decided to write yet another series of posts about the Linux kernel for **x86_64**. Note that I'm not a professional kernel hacker, and I don't write code for the kernel at work. It's just a hobby. I just like low-level stuff, and it is interesting for me to see how these things work. So if you notice anything confusing, or if you have any questions/remarks, ping me on twitter [0xAX](https://twitter.com/0xAX), drop me an [email](anotherworldofworld@gmail.com) or just create an [issue](https://github.com/0xAX/linux-insides/issues/new). I appreciate it. All posts will also be accessible at [linux-insides](https://github.com/0xAX/linux-insides) and if you find something wrong with my English or post content, feel free to send pull request. *Note that this isn't official documentation, just learning and sharing knowledge.* **Required knowledge** * Understanding C code * Understanding assembly code (AT&T syntax) Anyway, if you just started to learn some tools, I will try to explain some parts during this and following posts. Ok, little introduction finished and now we can start to dive into kernel and low-level stuff. All code is actual for kernel - 3.18, if there are changes, I will update posts. Magic power button, what's next? -------------------------------------------------------------------------------- Despite that this is a series of posts about linux kernel, we will not start from kernel code (at least in this paragraph). Ok, you pressed magic power button on your laptop or desktop computer and it started to work. After the motherboard sends a signal to the [power supply](https://en.wikipedia.org/wiki/Power_supply), the power supply provides the computer with the proper amount of electricity. Once motherboard receives the [power good signal](https://en.wikipedia.org/wiki/Power_good_signal), it tries to run the CPU. The CPU resets all leftover data in its registers and sets up predefined values for every register. [80386](https://en.wikipedia.org/wiki/Intel_80386) and later CPUs define the following predefined data in CPU registers after the computer resets: ``` IP 0xfff0 CS selector 0xf000 CS base 0xffff0000 ``` The processor starts working in [real mode](https://en.wikipedia.org/wiki/Real_mode) now and we need to make a little retreat for understanding memory segmentation in this mode. Real mode is supported in all x86-compatible processors, from [8086](https://en.wikipedia.org/wiki/Intel_8086) to modern Intel 64-bit CPUs. The 8086 processor had a 20-bit address bus, which means that it could work with 0-2^20 bytes address space (1 megabyte). But it only had 16-bit registers, and with 16-bit registers the maximum address is 2^16 or 0xffff (64 kilobytes). Memory segmentation was used to make use of all of the address space. All memory was divided into small, fixed-size segments of 65535 bytes, or 64 KB. Since we cannot address memory behind 64 KB with 16 bit registers, another method to do it was devised. An address consists of two parts: the beginning address of the segment and the offset from the beginning of this segment. To get a physical address in memory, we need to multiply the segment part by 16 and add the offset part: ``` PhysicalAddress = Segment * 16 + Offset ``` For example `CS:IP` is `0x2000:0x0010`. The corresponding physical address will be: ```python >>> hex((0x2000 << 4) + 0x0010) '0x20010' ``` But if we take the biggest segment part and offset: `0xffff:0xffff`, it will be: ```python >>> hex((0xffff << 4) + 0xffff) '0x10ffef' ``` which is 65519 bytes over first megabyte. Since only one megabyte is accessible in real mode, `0x10ffef` becomes `0x00ffef` with disabled [A20](https://en.wikipedia.org/wiki/A20_line). Ok, now we know about real mode and memory addressing. Let's get back to register values after reset. `CS` register consists of two parts: the visible segment selector and hidden base address. We know predefined `CS` base and `IP` value, logical address will be: ``` 0xffff0000:0xfff0 ``` In this way starting address formed by adding the base address to the value in the EIP register: ```python >>> 0xffff0000 + 0xfff0 '0xfffffff0' ``` We get `0xfffffff0` which is 4GB - 16 bytes. This point is the [Reset vector](http://en.wikipedia.org/wiki/Reset_vector). This is the memory location at which CPU expects to find the first instruction to execute after reset. It contains a [jump](http://en.wikipedia.org/wiki/JMP_%28x86_instruction%29) instruction which usually points to the BIOS entry point. For example, if we look in [coreboot](http://www.coreboot.org/) source code, we will see it: ```assembly .section ".reset" .code16 .globl reset_vector reset_vector: .byte 0xe9 .int _start - ( . + 2 ) ... ``` We can see here jump instruction [opcode](http://ref.x86asm.net/coder32.html#xE9) - 0xe9 to the address `_start - ( . + 2)`. And we can see that `reset` section is 16 bytes and starts at `0xfffffff0`: ``` SECTIONS { _ROMTOP = 0xfffffff0; . = _ROMTOP; .reset . : { *(.reset) . = 15 ; BYTE(0x00); } } ``` Now the BIOS has started to work. After initializing and checking the hardware, it needs to find a bootable device. A boot order is stored in the BIOS configuration, controlling which devices the kernel attempts to boot. In the case of attempting to boot a hard drive, the BIOS tries to find a boot sector. On hard drives partitioned with an MBR partition layout, the boot sector is stored in the first 446 bytes of the first sector (512 bytes). The final two bytes of the first sector are `0x55` and `0xaa` which signals the BIOS that the device as bootable. For example: ```assembly ; ; Note: this example written with Intel syntax ; [BITS 16] [ORG 0x7c00] boot: mov al, '!' mov ah, 0x0e mov bh, 0x00 mov bl, 0x07 int 0x10 jmp $ times 510-($-$$) db 0 db 0x55 db 0xaa ``` Build and run it with: ``` nasm -f bin boot.nasm && qemu-system-x86_64 boot ``` This will instruct [QEMU](http://qemu.org) to use the `boot` binary we just built as a disk image. Since the binary generated by the assembly code above fulfills the requirements of the boot sector (the origin is set to 0x7c00, and we end with the magic sequence), QEMU will treat the binary as the master boot record of a disk image. We will see: ![Simple bootloader which prints only `!`](http://oi60.tinypic.com/2qbwup0.jpg) In this example we can see that this code will be executed in 16 bit real mode and will start at 0x7c00 in memory. After the start it calls the [0x10](http://www.ctyme.com/intr/rb-0106.htm) interrupt which just prints `!` symbol. It fills rest of 510 bytes with zeros and finish with two magic bytes `0xaa` and `0x55`. Although you can see binary dump of it with `objdump` util: ``` nasm -f bin boot.nasm objdump -D -b binary -mi386 -Maddr16,data16,intel boot ``` A real-world boot sector has code for continuing the boot process and the partition table... instead of a bunch of 0's and an exclamation point :) Ok, so, from this moment BIOS handed control to the bootloader and we can go ahead. **NOTE**: as you can read above the CPU is in real mode. In real mode, calculating the physical address in memory is as follows: ``` PhysicalAddress = Segment * 16 + Offset ``` as I wrote above. But we have only 16 bit general purpose registers. The maximum value of 16 bit register is: `0xffff`; So if we take the biggest values, it will be: ```python >>> hex((0xffff * 16) + 0xffff) '0x10ffef' ``` Where `0x10ffef` is equal to `1mb + 64KB - 16b`. But a [8086](https://en.wikipedia.org/wiki/Intel_8086) processor, which was first processor with real mode, had 20 bit address line, and `2^20 = 1048576.0` is 1MB, so it means that actually available memory amount is 1MB. General real mode's memory map is: ``` 0x00000000 - 0x000003FF - Real Mode Interrupt Vector Table 0x00000400 - 0x000004FF - BIOS Data Area 0x00000500 - 0x00007BFF - Unused 0x00007C00 - 0x00007DFF - Our Bootloader 0x00007E00 - 0x0009FFFF - Unused 0x000A0000 - 0x000BFFFF - Video RAM (VRAM) Memory 0x000B0000 - 0x000B7777 - Monochrome Video Memory 0x000B8000 - 0x000BFFFF - Color Video Memory 0x000C0000 - 0x000C7FFF - Video ROM BIOS 0x000C8000 - 0x000EFFFF - BIOS Shadow Area 0x000F0000 - 0x000FFFFF - System BIOS ``` But stop, at the beginning of post I wrote that first instruction executed by the CPU is located at address `0xfffffff0`, which is much bigger than `0xfffff` (1MB). How can CPU access it in real mode? As I write about and you can read in [coreboot](http://www.coreboot.org/Developer_Manual/Memory_map) documentation: ``` 0xFFFE_0000 - 0xFFFF_FFFF: 128 kilobyte ROM mapped into address space ``` At the start of execution BIOS is not in RAM, it is located in ROM. Bootloader -------------------------------------------------------------------------------- There are a number of bootloaders which can boot Linux, such as [GRUB 2](https://www.gnu.org/software/grub/) and [syslinux](http://www.syslinux.org/wiki/index.php/The_Syslinux_Project). The Linux kernel has a [Boot protocol](https://github.com/torvalds/linux/blob/master/Documentation/x86/boot.txt) which specifies the requirements for bootloaders to implement Linux support. This example will describe GRUB 2. Now that the BIOS has chosen a boot device and transferred control to the boot sector code, execution starts from [boot.img](http://git.savannah.gnu.org/gitweb/?p=grub.git;a=blob;f=grub-core/boot/i386/pc/boot.S;hb=HEAD). This code is very simple due to the limited amount of space available, and contains a pointer that it uses to jump to the location of GRUB 2's core image. The core image begins with [diskboot.img](http://git.savannah.gnu.org/gitweb/?p=grub.git;a=blob;f=grub-core/boot/i386/pc/diskboot.S;hb=HEAD), which is usually stored immediately after the first sector in the unused space before the first partition. The above code loads the rest of the core image into memory, which contains GRUB 2's kernel and drivers for handling filesystems. After loading the rest of the core image, it executes [grub_main](http://git.savannah.gnu.org/gitweb/?p=grub.git;a=blob;f=grub-core/kern/main.c). `grub_main` initializes console, gets base address for modules, sets root device, loads/parses grub configuration file, loads modules etc... At the end of execution, `grub_main` moves grub to normal mode. `grub_normal_execute` (from `grub-core/normal/main.c`) completes last preparation and shows a menu for selecting an operating system. When we select one of grub menu entries, `grub_menu_execute_entry` begins to be executed, which executes grub `boot` command. It starts to boot operating system. As we can read in the kernel boot protocol, the bootloader must read and fill some fields of kernel setup header which starts at `0x01f1` offset from the kernel setup code. Kernel header [arch/x86/boot/header.S](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S) starts from: ```assembly .globl hdr hdr: setup_sects: .byte 0 root_flags: .word ROOT_RDONLY syssize: .long 0 ram_size: .word 0 vid_mode: .word SVGA_MODE root_dev: .word 0 boot_flag: .word 0xAA55 ``` The bootloader must fill this and the rest of the headers (only marked as `write` in the linux boot protocol, for example [this](https://github.com/torvalds/linux/blob/master/Documentation/x86/boot.txt#L354)) with values which it either got from command line or calculated. We will not see description and explanation of all fields of kernel setup header, we will get back to it when kernel uses it. Anyway, you can find description of any field in the [boot protocol](https://github.com/torvalds/linux/blob/master/Documentation/x86/boot.txt#L156). As we can see in kernel boot protocol, the memory map will be the following after kernel loading: ```shell | Protected-mode kernel | 100000 +------------------------+ | I/O memory hole | 0A0000 +------------------------+ | Reserved for BIOS | Leave as much as possible unused ~ ~ | Command line | (Can also be below the X+10000 mark) X+10000 +------------------------+ | Stack/heap | For use by the kernel real-mode code. X+08000 +------------------------+ | Kernel setup | The kernel real-mode code. | Kernel boot sector | The kernel legacy boot sector. X +------------------------+ | Boot loader | <- Boot sector entry point 0x7C00 001000 +------------------------+ | Reserved for MBR/BIOS | 000800 +------------------------+ | Typically used by MBR | 000600 +------------------------+ | BIOS use only | 000000 +------------------------+ ``` So after the bootloader transferred control to the kernel, it starts somewhere at: ``` 0x1000 + X + sizeof(KernelBootSector) + 1 ``` where `X` is the address kernel bootsector loaded. In my case `X` is `0x10000` (), we can see it in memory dump: ![kernel first address](http://oi57.tinypic.com/16bkco2.jpg) Ok, bootloader loaded linux kernel into memory, filled header fields and jumped to it. Now we can move directly to the kernel setup code. Start of kernel setup -------------------------------------------------------------------------------- Finally we are in the kernel. Technically kernel didn't run yet, first of all we need to setup kernel, memory manager, process manager, etc. Kernel setup execution starts from [arch/x86/boot/header.S](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S) at the [_start](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S#L293). It is little strange at the first look, there are many instructions before it. Actually.... Long time ago linux had its own bootloader, but now if you run for example: ``` qemu-system-x86_64 vmlinuz-3.18-generic ``` You will see: ![Try vmlinuz in qemu](http://oi60.tinypic.com/r02xkz.jpg) Actually `header.S` starts from [MZ](https://en.wikipedia.org/wiki/DOS_MZ_executable) (see image above), error message printing and following [PE](https://en.wikipedia.org/wiki/Portable_Executable) header: ```assembly #ifdef CONFIG_EFI_STUB # "MZ", MS-DOS header .byte 0x4d .byte 0x5a #endif ... ... ... pe_header: .ascii "PE" .word 0 ``` It needs this for loading operating system with [UEFI](https://en.wikipedia.org/wiki/Unified_Extensible_Firmware_Interface). Here we will not see how it works (will look into it in the next parts). So actual kernel setup entry point is: ``` // header.S line 292 .globl _start _start: ``` Bootloader (grub2 and others) knows about this point (`0x200` offset from `MZ`) and makes a jump directly to this point, despite the fact that `header.S` starts from `.bstext` section which prints error message: ``` // // arch/x86/boot/setup.ld // . = 0; // current position .bstext : { *(.bstext) } // put .bstext section to position 0 .bsdata : { *(.bsdata) } ``` So kernel setup entry point is: ```assembly .globl _start _start: .byte 0xeb .byte start_of_setup-1f 1: // // rest of the header // ``` Here we can see `jmp` instruction opcode - `0xeb` to the `start_of_setup-1f` point. `Nf` notation means following: `2f` refers to the next local `2:` label. In our case it is label `1` which goes right after jump. It contains rest of setup [header](https://github.com/torvalds/linux/blob/master/Documentation/x86/boot.txt#L156) and right after setup header we can see `.entrytext` section which starts at `start_of_setup` label. Actually it's first code which starts to execute besides previous jump instruction. After kernel setup got the control from bootloader, first `jmp` instruction is located at `0x200` (first 512 bytes) offset from the start of kernel real mode. This we can read in linux kernel boot protocol and also see in grub2 source code: ```C state.gs = state.fs = state.es = state.ds = state.ss = segment; state.cs = segment + 0x20; ``` It means that segment registers will have following values after kernel setup starts to work: ``` fs = es = ds = ss = 0x1000 cs = 0x1020 ``` for my case when kernel loaded at `0x10000`. After jump to `start_of_setup`, needs to do following things: * Be sure that all values of all segment registers are equal * Setup correct stack if need * Setup [bss](https://en.wikipedia.org/wiki/.bss) * Jump to C code at [main.c](https://github.com/torvalds/linux/blob/master/arch/x86/boot/main.c) Let's look at implementation. Segment registers align -------------------------------------------------------------------------------- First of all it ensures that `ds` and `es` segment registers point to the same address and enables interrupts with `sti` instruction: ```assembly movw %ds, %ax movw %ax, %es sti ``` As i wrote above, grub2 loads kernel setup code at `0x10000` address and `cs` at `0x1020` because execution doesn't start from the start of file, but from: ``` _start: .byte 0xeb .byte start_of_setup-1f ``` jump, which is 512 bytes offset from the [4d 5a](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S#L47). Also need to align `cs` from 0x10200 to 0x10000 as all other segment registers. After that we setup stack: ```assembly pushw %ds pushw $6f lretw ``` push `ds` value to stack, and address of [6](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S#L494) label and execute `lretw` instruction. When we call `lretw`, it loads address of `6` label to [instruction pointer](https://en.wikipedia.org/wiki/Program_counter) register and `cs` with value of `ds`. After it we will have `ds` and `cs` with the same values. Stack setup -------------------------------------------------------------------------------- Actually, almost all of the setup code is preparation for C language environment in the real mode. The next [step](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S#L467) is checking of `ss` register value and making of correct stack if `ss` is wrong: ```assembly movw %ss, %dx cmpw %ax, %dx movw %sp, %dx je 2f ``` Generally, it can be 3 different cases: * `ss` has valid value 0x10000 (as all other segment registers beside `cs`) * `ss` is invalid and `CAN_USE_HEAP` flag is set (see below) * `ss` is invalid and `CAN_USE_HEAP` flag is not set (see below) Let's look at all of these cases: 1. `ss` has a correct address (0x10000). In this case we go to [2](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S#L481) label: ``` 2: andw $~3, %dx jnz 3f movw $0xfffc, %dx 3: movw %ax, %ss movzwl %dx, %esp sti ``` Here we can see aligning of `dx` (contains `sp` given by bootloader) to 4 bytes and checking that it is not zero. If it is zero we put `0xfffc` (4 byte aligned address before maximum segment size - 64 KB) to `dx`. If it is not zero we continue to use `sp` given by bootloader (0xf7f4 in my case). After this we put `ax` value to `ss` which stores correct segment address `0x10000` and set up correct `sp`. After it we have correct stack: ![stack](http://oi58.tinypic.com/16iwcis.jpg) 2. In the second case (`ss` != `ds`), first of all put [_end](https://github.com/torvalds/linux/blob/master/arch/x86/boot/setup.ld#L52) (address of end of setup code) value in `dx`. And check `loadflags` header field with `testb` instruction too see if we can use heap or not. [loadflags](https://github.com/torvalds/linux/blob/master/arch/x86/boot/header.S#L321) is a bitmask header which is defined as: ```C #define LOADED_HIGH (1<<0) #define QUIET_FLAG (1<<5) #define KEEP_SEGMENTS (1<<6) #define CAN_USE_HEAP (1<<7) ``` And as we can read in the boot protocol: ``` Field name: loadflags This field is a bitmask. Bit 7 (write): CAN_USE_HEAP Set this bit to 1 to indicate that the value entered in the heap_end_ptr is valid. If this field is clear, some setup code functionality will be disabled. ``` If `CAN_USE_HEAP` bit is set, put `heap_end_ptr` to `dx` which points to `_end` and add `STACK_SIZE` (minimal stack size - 512 bytes) to it. After this if `dx` is not carry, jump to `2` (it will be not carry, dx = _end + 512) label as in previous case and make correct stack. ![stack](http://oi62.tinypic.com/dr7b5w.jpg) 3. The last case when `CAN_USE_HEAP` is not set, we just use minimal stack from `_end` to `_end + STACK_SIZE`: ![minimal stack](http://oi60.tinypic.com/28w051y.jpg) Bss setup -------------------------------------------------------------------------------- The last two steps that need to happen before we can jump to the main C code, are that we need to set up the [bss](https://en.wikipedia.org/wiki/.bss) area, and check the "magic" signature. Firstly, signature checking: ```assembly cmpl $0x5a5aaa55, setup_sig jne setup_bad ``` This simply consists of comparing the [setup_sig](https://github.com/torvalds/linux/blob/master/arch/x86/boot/setup.ld#L39) against the magic number `0x5a5aaa55`; if they are not equal, a fatal error is reported. But if the magic number matches, knowing we have a set of correct segment registers, and a stack, we need only setup the bss section before jumping into the C code. The bss section is used for storing statically allocated, uninitialized, data. Linux carefully ensures this area of memory is first blanked, using the following code: ```assembly movw $__bss_start, %di movw $_end+3, %cx xorl %eax, %eax subw %di, %cx shrw $2, %cx rep; stosl ``` First of all the [__bss_start](https://github.com/torvalds/linux/blob/master/arch/x86/boot/setup.ld#L47) address is moved into `di`, and the `_end + 3` address (+3 - aligns to 4 bytes) is moved into `cx`. The `eax` register is cleared (using an `xor` instruction), and the bss section size (`cx`-`di`) is calculated and put into `cx`. Then, `cx` is divided by four (the size of a 'word'), and the `stosl` instruction is repeatedly used, storing the value of `eax` (zero) into the address pointed to by `di`, and automatically increasing `di` by four (this occurs until `cx` reaches zero). The net effect of this code, is that zeros are written through all words in memory from `__bss_start` to `_end`: ![bss](http://oi59.tinypic.com/29m2eyr.jpg) Jump to main -------------------------------------------------------------------------------- That's all, we have stack, bss and now we can jump to `main` C function: ```assembly calll main ``` which is in [arch/x86/boot/main.c](https://github.com/torvalds/linux/blob/master/arch/x86/boot/main.c). What will be there? We will see it in the next part. Conclusion -------------------------------------------------------------------------------- This is the end of the first part about linux kernel internals. If you have questions or suggestions, ping me in twitter [0xAX](https://twitter.com/0xAX), drop me [email](anotherworldofworld@gmail.com) or just create [issue](https://github.com/0xAX/linux-internals/issues/new). In the next part we will see first C code which executes in linux kernel setup, implementation of memory routines as memset, memcpy, `earlyprintk` implementation and early console initialization and many more. **Please note that English is not my first language and I am really sorry for any inconvenience. If you found any mistakes please send me PR to [linux-internals](https://github.com/0xAX/linux-internals).** Links -------------------------------------------------------------------------------- * [Intel 80386 programmer's reference manual 1986](http://css.csail.mit.edu/6.858/2014/readings/i386.pdf) * [Minimal Boot Loader for IntelĀ® Architecture](https://www.cs.cmu.edu/~410/doc/minimal_boot.pdf) * [8086](http://en.wikipedia.org/wiki/Intel_8086) * [80386](http://en.wikipedia.org/wiki/Intel_80386) * [Reset vector](http://en.wikipedia.org/wiki/Reset_vector) * [Real mode](http://en.wikipedia.org/wiki/Real_mode) * [Linux kernel boot protocol](https://www.kernel.org/doc/Documentation/x86/boot.txt) * [CoreBoot developer manual](http://www.coreboot.org/Developer_Manual) * [Ralf Brown's Interrupt List](http://www.ctyme.com/intr/int.htm) * [Power supply](http://en.wikipedia.org/wiki/Power_supply) * [Power good signal](http://en.wikipedia.org/wiki/Power_good_signal)